Market update series Glass fabric, copper foil, AI demand: the current state of PCB base materials. Read the latest post →
Published — 29 October 2026 Market update series

HVLP4 copper foil: why AI hardware places new demands on PCB input materials

In fast electrical connections, the copper surface influences how well a signal reaches its destination. This is becoming increasingly relevant in high-performance servers and network systems. In the Lexington documents, HVLP4 denotes a generation of particularly smooth copper foils for demanding applications. To assess its benefit correctly, the surface profile, the material combination and the requirements of the complete transmission channel have to be considered together.

Why the surface matters at high frequencies

As frequency rises, the current density concentrates more strongly in the regions of a conductor close to the surface. This relationship is known as the skin effect. The characteristic skin depth decreases as it does so. A technical article by Rogers on the selection of copper foils gives, for example, around 2.1 micrometres at 1 gigahertz and around 0.66 micrometres at 10 gigahertz for copper.

When the surface roughness becomes relevant in relation to this depth, it can increase conductor losses. How strongly this affects insertion loss also depends on the design and the frequency. A high data rate alone therefore does not yet imply a universal foil requirement. What is decisive is the loss contribution that the specific PCB construction is permitted to cause in the intended channel.

What the designation HVLP4 tells you

HVLP stands for a copper foil with a particularly low profile. The generation designations used in market documents help with rough classification. For a technical approval, however, the indication HVLP4 is not sufficient. What is relevant are the specific product, the treated surface, the measurement method and the properties guaranteed by the manufacturer.

Roughness parameters such as Rz and Rq, for instance, are not simply interchangeable. Figures for different sides of the foil can also lead to values that appear similar but are in fact not comparable. The Lexington HVLP4 analysis gives indicative values for classification. A project specification should instead contain traceable product data and agreed measurement conditions. This puts a material comparison on a verifiable footing.

The material combination determines the result

A smooth copper foil can have a favourable influence on conductor losses. At the same time, losses arise in the dielectric material, that is, in the insulating composite of the construction. Resin system, glass fabric, geometry and the interconnection technology all contribute to the behaviour of the channel. The choice of foil should therefore be part of a joint consideration of the entire construction.

The Lexington documents accordingly emphasise the interplay with suitable resins and glass fabrics. A low dielectric constant and a low dissipation factor fulfil different functions here. They should not be treated as equivalent quality characteristics. Which properties are needed follows from the electrical requirements, the design and the conditions under which the PCB is operated and processed.

Smoothness and processability have to match

Material selection also includes the question of how reliably copper and insulating material function together in the composite. The surface has to be suitable for the intended resin system; electrical advantages must not be assessed in isolation from adhesion and process stability. Manufacturers use defined surface treatments for this purpose. The suitable combination therefore cannot be derived solely from a roughness value that is as small as possible.

Reproducibility is equally important. A single favourable measured value on a sample does not yet say how stable the properties remain across series production volumes and processing steps. For approval it should be established which data are needed on the base material, on the laminate and on a representative PCB. The scope of testing depends on the project and on the change made in each case.

Plan qualification in good time

The Lexington market analysis of September 2026 places qualified, actually usable capacity at the centre. What counts for a project is whether the material offered meets the requirements in the intended combination. An available foil volume can only help once the materials and PCBs made from it are suitable for the application and approved accordingly.

For alternatives, a coordinated assessment is therefore advisable before time pressure arises. This includes traceable material data and, where the application requires it, measurements on suitable test structures or representative constructions. There is no blanket qualification period for all projects. Likewise, not every new batch automatically triggers a complete requalification; what matters are the agreed change rules and relevant deviations.

For coordination with Lexington®, you should state not only the desired material class but also the stackup, the electrical requirements and the intended evidence. This allows HVLP4 to be assessed as a component of a suitable material solution. The benefit arises from the interplay of specification, processing and verified performance in the actual construction.

Market update: the situation at a glance →

More articles

[ Read on ]

A question about this?

If something here touches a board you are working on, ask. You get an engineer, not a contact form auto-reply.